R
PLCD27
WNER'S MANUAL
CD PLAYER
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
To prevent injury of fire,take the
following precautions:
To prevent damage to the machine,
take the following precautions:
Attaching panel
Attach the front panel by fixing
the left side of it into this unit as1
showing.Then push the right side
of panel towards into connecting
plug as 2 showing.
Insert the unit unitll it is firmly locked to the
main unit, otherwise it may
Be sure the unit is connected to a 12V
DC power with a Negative Ground
fall out of place when jolted
The unit is only designed for use with 4
speakers. Do not combine output for use
with 2 speakers. Do not ground negative
speaker leads to the chassis ground
Do not open the top cover and do not install
the unit in
When extending the ignition, memory
back up or ground cable, use diameter of
0.75mm(AWG18) or
more automotive grade cable to avoid wire
deterioration or damage
to the wire coating.
place where it is exposed to direct sunlight
(including the faceplate),in order to avoid high
heat or humidity, water splash over it or dust.
Do not touch the terminals of the units.
Attaching panel
To prevent short circuit, never put or leave
any metallic object into the unit.
If you smell or see smoke, turn off the
power immediately and consult your dealer.
Be careful not to drop or shock the unit
strongly, it may break or crack because it
contain glass parts.
If you have difficulty in installing this unit
in your vehicle. Please contact your dealer.
If the unit seems not work in properly press
the reset buttonto reset the memory of the
unit.
2
POWER ON/
OFF/VOLUME
Volume
PLAY/PAUSE
EJECT
Increasing volume
EJECT
Rotate the [VOL+]button
VOL
Decreasing
Rotate the [VOL-]button
BD
CD
PUSH
ON/OFF
TOP
SCAN
REPEAT
RANDOM
STOP
DSP
CLK
1
2
3
4
5
6
SELECT
CLOCK
RELEASE SELECT DSP
Play/pause
Play
Press the [CD]button
LCD display
Pause
Press again the [CD]button
Power
Turning ON the power
If a disc has already been loaded, CDIN would be shown on
the display, press this button to start play disc even though
the unit is in Radio mode. When disc
is playing, press this button to
Press the [PWR]button.
pause the disc, press again
Press to turn on the unit power,Press the button to turn off
the unit.
to resume the normal play.
BD
CD
DOM
STOP
CLK
5
6
3
Hour
Eject
Press [
] button to adjust the hour.
Out
Minute
Press the [ ]button ,if having adisc in the unit.
The disc will be ejected out.
Press [ ] button to adjust the minute.
Quit clock set mode
If there no operation in 5 second, it will quit clock
set mode.
In
Press the [ ]button again, the disc
will be load in.
In beam mode, press the BD button can enter radio
mode. If the disc in the slot, press the EJECT button to
eject the disc form the slot and automatically be
switched to the radio mode.
LOUD/DSP
LOUD
In radio mode, if push a disc into slot, the disc will
automatic insert and begins to play. If the disc in the solt,
press PLAY/PAUSE button to play the disc again.
Long press the DSP button to emphasize the bass output,
press it again to resume the normal listening.
DSP
Short press this button to DSP
Press DSP button once, ROCK will bicker on display.
Press DSP button twice, POP will bicker on display.
Press DSP button third, CLASS will bicker on display.
Clock
Press CLK can display time. Time will display even
power off.
Long Press CLK for 3 second will into clock set mode.
Release
press the "
" button to release faceplate.
4
VOL+/-
Speaker mode
EJECT
VOL
VOLUME
TREBLE
BASS
BD
CD
PUSH
ON/OFF
TOP
1
SCAN
REPEAT
RANDOM
STOP
DSP
CLK
2
3
4
5
6
SELECT
FADER
BALANCE
SCAN
RANDOM
REPEAT
SELECT
TOP
STOP
In press mode, VOL is sel function
Treble set mode
Volume set mode
Press SEL button third,
display shows TRE ,then
rotate the volume button to adjust treble
Press SEL button once,display shows VOL
then rotate the volume button
to adjust volume level up.Rotate
the volume button to
,
+
+
VOL
level up. Rotate the volume
treble level down.
-
buttonto adjust
-
SEL
adjust volume
level down.
PRESS
Balance set mode
SELECT
Press SEL button fourth
display shows BAL ,then
PRESS
rotate the volume
to adjust left speaks level .
Rotate the volume button
to adjust right speaks level .
+
button
Bass set mode
-
Press SEL button twice,display shows BAS
then rotate the volume button to adjust bass
button to adjust
,
+
level up. Rotate the volume
bass level down.
-
Fader set mode
Press SEL button fifth,display shows FAD ,then
rotate the volume button to adjust front speaks
buttonto adjust back
+
level. Rotate the volume
speaks level.
-
5
Top
Scan
Press [TOP]button
Press [SCN]button
Select the first track directly
Press this button once for TRACK INTRODUCTION,the first
ten seconds of each track on the disc will paly. To confirm
the track number. Press it again while playing on the desired
track. SCAN will appear on the display.Press it again to
stop it.
In CD mode,press this button, the first track will play.
Repeat
Press [RPT]button
Stop
Press the button once to repeat the same track continuously,
Press the button twice to repeat the disc continuously,
RPT will appear on the LCD display.
Press [STOP]button
Press this button once to stop play music .
Random
Press [RDM]button
Press this button to play all the track inrandom order. RDM
will appear on the display. Press it again to stop random playing.
This button is invalid ifthe unit is in PBC On mode.
6
SEEK- SEEK+
Tune
In radio mode:
EJECT
manual tuning:
VOL
short press
Short press
button it can select higher frequency station.
can select lower frequency station.
BD
CD
PUSH
ON/OFF
TOP
SCAN
REPEAT
RANDOM
STOP
CLK
DSP
1
2
3
4
5
6
SELECT
Auto loading tuning:
the long press
button it can automatically select higher
BAND
PRESET MEMORY 1-6
frequency station. And the long press
select lower frequency station.
it can automatically
Band
Selecting band
Press BAND button to select among three FM or two AM bands.
(FM1-FM2-FM3-AM1-AM2)
ST
Frequency
7
Loading and replacing the battery
Use one lithium battery(CR2025)
insert the batteries with the +and - poles aligned properly.
Following the illustration inside the case.
Pull out
APS
MONO
TOP
LOUD
CLK
STOP
Store unused batteries out of the reach of children. Contact a
doctor immediately if the battery is accidentally swallowed.
RPT
Do not set the remote on hot places such as above the dashboard.
SCAN
Basic operation
RDM
Turning ON the power
Press the [ ]button.
Press to turn on the unit power,Press the button to turn off
the unit.
8
External view
........ Number of items
External view
........ Number of items
Volume
Increasing volume
Press the [+]loud VOL
Increasing volume
Press the [-]low VOL
1
2
5
6
............1
............1
............1
............1
Play/pause
Play
Press the [ ]button
Pause
3
4
7
8
............1
............2
............1
............1
Press the [ ] button again
APS
MONO
TOP
LOUD
CLK
STOP
RPT
SCAN
RDM
Radio control
Page(7)
The use of any accessories except of those provided
might result in damage to the unit .make sure only to
use the accessories shipped with the unit ,as shown
above.
Remote operation the same
of mainframe.
9
Follow this easy wiring diagram in order to enable you to install
the new or existing RADIO and SPEAKER wring system.
SPEAKER WIRING
The unit is only designed for the use with 4 speakers system, it can
only be connected with speakers rated in the load impedance range
from 4 to 8 ohms. Load impedance less than 4 ohms could damage
the unit.
Be sure the unit is connected to a 12 volts battery with negative ground.
Good ground connections eliminate most electrical noise problem and
require tight with the metal vehicle chassis. remove plastic, paint or dust
for good electrical contact.
Never combine (BRIDGE) the outputs for use with 2 speakers, and
Never ground any Negative speaker to the chassis ground.
CAR ANTENNA
RED RCH
CAR ANTENNA
LCH RCA line out
RED RCH
WHITE
RCA line out
WHITE LCH
Connect to control for antenna
or remote control for amplifier.
Orange
YELLOW
Memory+
Grey
Green
Connect to battery or +12 volts of
power source that is always live.
Green
/white
Grey
/white
Black
Red
Ground-
Right Front
Left Front
Brown
Blue
12V+
Brown
/white
Blue
/white
Connect to lgnition key switch.
Right Rear
Left Rear
10
Before installing the receiver permanently, fit it in the approximate place in your car Connect the
equipment according to the speakers and electrical connections. When
your system is operated properly,(preferably with the
car engine running), follow the instructions
for permanent installation
of your system.
3)Support strap
(supplied)
INSTALL THE UNIT
1)Install half sleeve, can be with or
without adapter. It will fit better
with adapter.
2)Bend over some tabs where possible
2)Bend over tabs
of half sleeve
(supplied)
tosecure the half sleeve inside of dash.
3) Support strap to bestrutted under
dash, secure this strip to avoid skipp
ing of disc.
1) Adapter
(not supplied)
Half sleeve
(supplied)
REMOVING THE UNIT
Insert removal wrench into the small
gap on the right side of the unit and pull
the unit slightly out on the same side,
then release the wrench. Repeat the
same action for the left side. By now,
you can remove the unit and unplug
the wires connector.
4) Two wrenches for release
the unit (supplied)
11
Specifications subject to change without notice.
CD PLAYER
GENERAL
Signal/Noise radio......................................................70dB
Frequency response..............................20Hz-20KHz(+3dB)
Channel separation..................................................>45dB
Dual D/A converter.......................................................16Bit
Operating power.....................................12 Volts DC,negative
ground
%10THD output wiring.........................Designed for using four
speakers only front and rear
channels cannot be combined
in use with 2speakers.
FM Tuner
Load impedance..................................compatible 4 to 8 ohm
speakers
Tuning range............................................USA:87.5-108MHz
(100KHz step)
Fuses........................................................1amp and 10 amp
Dimensions...........................................178mm(L)x50mm(W)
x150mm(H)
EUROPE:87.5-108.0MHz
(50KHz step)
FM usable sensitivity(S/N=30dB)..............................<12dB
Stereo separation.....................................................>45dB
Weight......................................................................2.5Kgs
AM Tuner
Tuning range...........................................USA:520-1720KHz
(10KHz step)
EUROPE:522-1620KHz
(9KHz step)
AM sensitivity..............................................................28dB
12
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
?No/Poor sound on one or more speakers
Speakers or speaker wiring or volume, Balance and
Fader setting
Check the speaker wiring and test the speakers all in good condition
check the setting of volume, Balance and Fader controls.
?The power does not turn ON.
The fuse has blown.
Install half sleeve, can be with or
?CD sound skips
Installation the unit angle is greater than 45 ,or
mounting is not fixed and the back strap is not secure.
?NO Sound.
The cable connect incorrectness.
Adjust the unit with mounting angle less than 45 and make sure the
unit is mounted securely and tighten with the back strap(supplied)
Exactitude connect of the cable.
?Noise on Radiopoor recepiton
Antenna and Antenna Cable.
?Unit completely inoperative, no Light and Sound
Incorrect wire connection, Power RED/YELLOW or
Ground wire or Blown fuse
Check antenna and antenna cable, the antenna base must be
grounded and connected with good condition, repace
antenna or antenna cable if needed.
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to
+12 Volts battery and black wire to ground. Check Fuse with red/yellow
wire, or check the fuse block on your car.
?Noise on both Radio and CD
Poor ground,dirty or corroded at the car Battery posts
Check the black wire for proper grounding clean and tighten ground
connection.
13
C
a
r
A
u
d
i
o
H
i
f
i
S
y
s
t
e
m
|